Precautions for installation of metal coil curtain door - metal coil curtain company

Ụbọchị:2021-07-06Ọtụ:1143

This installation process standard is applicable to the installation of metal coil curtain doors in this project.

 

metal coil curtain

 

1. The structure of the metal coil curtain door

The metal coil curtain door is composed of curtain plate, roll body, guide rail, motor drive and other parts. The curtain plate is made of 1.5mm thick brushed stainless steel plate and made of C-shaped plate overlapping interlocking, which has the characteristics of good rigidity and excellent sealing performance.

 

2. Reserve a hole

The opening size of the metal coil curtain door is determined according to the construction site. To

 

 

3. Installation and debugging

The installation and debugging sequence of the metal coil curtain door is as follows:

(1) According to the design model, consult the product manual and electrical schematic diagram. Check the product surface treatment and spare parts. Measure the basic dimensions of each part of the product. Check whether the door opening is consistent with the size of the metal coil curtain door; whether the position and quantity of the embedded parts of the guide rail and bracket are correct. To

(2) Measure the elevation of the hole, and pop up the vertical lines of the two guide rails and the center line of the scroll. To

(3) Electric welding the backing plate on the embedded iron plate, fix the left and right brackets of the reel with screws, and install the reel. The reel should rotate flexibly after installation. To

(4) Install the reducer and transmission system. To

(5) Install electrical control system.

(6) No-load test run. To

(7) Install the pre-assembled curtain board on the reel.

(8) Install the guide rail. According to the position specified in the drawing, weld both sides and upper guide rails to the wall embedded parts and weld them into a whole. The guide rails should be on the same vertical plane. To

(9) Install the water curtain sprinkler system and connect it with the general control system. To

(10) Test run. Test run manually first, then open and close several times with the motor, adjust until there is no jam, blocking, abnormal noise, etc., all debugging is completed, and the protective cover is installed.

  • Ụzọ a ga - eji egwú a na - akwụsị n’ebe a na - akwụsị n’ebe a na - akwụsị n’ahụ́

    Ụzọ ịkụỤlọ a na - akwụsị n’ahụ́N’ebe a na - enwe mfe dị nnọọ mfe. Nke mbụ, a na - etinye otu ụgbọ mmiri n’okpuru, a na - emekwa ụgbọ mmiri ndị ọzọ nile n’elu n’elu ígwè a na - akpọ n’ahụ́. A na - egbo...

  • Ịkwasị nke ọ̀tụ̀tụ̀ òtù Drapery

    Dị ka òtù ahụ si kwuo,Ụzọ ígwè DraperyA na - ekewa n’ime eletrik ígwè Drapery na a na - enwe oké nri Drapery.Ọkpụkpụ ụgbọ mmiri na - eletrik bụ́ Drapery: ọ bụ ụgbọ mmiri na - eji ụgbọ mmiri na - akpọ....

  • Olee uru ndị a na - ewu ewu ewu n’ebe a na - arụ owuwu?

    Olee uru ndị ga - abara n’azụỤkwụN’owuwu ụlọ?N’ọrụ owuwu owuwu, a pụrụ ikwu na ụlọ ọrụ ahụ dị ebe nile. Anyị ekwesịghị ịma ọha na ihe mere anyị ji mara ya. Mgbe a na - echebe ụlọ ọrụ ahụ, ọ ga - enwe ...

  • Ụdị nche nke a na - eme ka a na - egbochi ụkwụ

    Ndọrọ nke e nwere n’ịkwụA na - akọ n’ụfụ:Nke a na - eme ka a ghara ịna - egbukepụ n’obodo a na - enwe n’ụzọ dị iche iche, n’ihi ya, ọ dị mkpa iji mee ka ọ̀tụ̀tụ̀ na mmetụta nke usoro ahụ.N’ozuzu, a na...

  • Ihe ndị mere e ji kwesị ịnọ n’ebe a na - akwụsị n’ahụ́

    Site n’otú ndị na - azụ ihe si ele ihe anya, ndị ahịa anyị na - amata ụlọ ọrụ anyị n’ebe nile1 Ịkwọ Ọma, ụlọ ọrụ ahụ nwere ìgwè ndị ọkachamara nke ndị na - edepụta ihe, ndị ọkà mmụta nwere ahụmahụ na ...

  • Ihe ndị e ji ákwà íṅụ

    Àgwà nke aÁkwà e ji ígwe:1. A na - eme ka ákwà a na - akpọ n'ahụ́ n'ahụ́ dị elu, aluminium alloy, brass, kopa na ihe ndị ọzọ. N’ihi ya, ákwà ígwè nwere ákwà dịgasị iche iche ndị mmadụ ga - ahọrọ. Ụdị ...

  • Ịrụ ákwà e ji ákwà e ji ígwú

    Ihe n'ahaÁkwà e ji ákwà aṅụ:(1) Ọ bụ ihe ndị a na - eme n’ihe ndị dị nta, dị obere na nke dị nro, bụ́ ndị a gafee, Dị ka a kparịrị ya ma jikọta ya.(2) ákwà a na - eji ákwà a na - eji ákwà e ji ígwè n’...

  • Ihe ọma

    Ihe a na - akụ n’agbụIhe ọmụma zụrụ:1. Họrọ ákwá ahụ dakwasị n’ihe ndị a na - enwe, nhọrọ ya bụ ihe bụ́ isi nhọrọ, Ị ga - ahọrọ ákwà ma ọ bụ nri ígwè. Ọ dị mfe imeghe ma mechie, ọ pụkwara imeghe windo...

leave your message